rear caliper to carrier pins advice
-
- Supporting Member I
- Posts: 57
- Joined: 04:25 pm Jan 12 2011
- Country:
rear caliper to carrier pins advice
my caliper is pretty sloppy on the carrier that it slides on. It looks like its just the pin on the carrier and the pin on the caliper that thread out. Is there any source for these pins?
Thanks in advance,
Joe
Thanks in advance,
Joe
- kdxquebec
- Supporting Member II
- Posts: 1255
- Joined: 07:18 am Nov 24 2004
- Country:
- Location: Québec:North Pole
- Contact:
Sorry I can't answer.casola wrote: Is there any source for these pins?
Do the holes in aluminium parts are worn out?
Happened to me...just got a complete ''like new'' 2003 KDX220 caliper and carrier bracket from Ebay.
BTW it was a direct bolt-on installation for my '89
'89 KDX 198cc '03 Gasgas Ec250 '13 Husaberg Te300
*CANADA* LEADING THE WORLD IN BEING JUST NORTH OF THE UNITED STATES.
*CANADA* LEADING THE WORLD IN BEING JUST NORTH OF THE UNITED STATES.
-
- Member
- Posts: 240
- Joined: 11:33 pm Dec 06 2006
- Country:
- Location: Newberg, Oregon
-
- Supporting Member I
- Posts: 57
- Joined: 04:25 pm Jan 12 2011
- Country:
- kdxquebec
- Supporting Member II
- Posts: 1255
- Joined: 07:18 am Nov 24 2004
- Country:
- Location: Québec:North Pole
- Contact:
Nocasola wrote:are they the same pins that hold in the brake pads?
Joe
Do the holes where the pin goes in the caliper and the carrier are worn out?
Last edited by kdxquebec on 04:43 pm Jan 25 2011, edited 1 time in total.
'89 KDX 198cc '03 Gasgas Ec250 '13 Husaberg Te300
*CANADA* LEADING THE WORLD IN BEING JUST NORTH OF THE UNITED STATES.
*CANADA* LEADING THE WORLD IN BEING JUST NORTH OF THE UNITED STATES.
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
u talkin about the one that goes into the black rubber piece filled up with grease?
I may have one laying around, will have to look. Try filling the rubber part with good thick grease should help. They are suppose to have some play.
A pic would help understand what exactly your are talking about
I may have one laying around, will have to look. Try filling the rubber part with good thick grease should help. They are suppose to have some play.
A pic would help understand what exactly your are talking about
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
-
- Supporting Member I
- Posts: 57
- Joined: 04:25 pm Jan 12 2011
- Country:
- kdxquebec
- Supporting Member II
- Posts: 1255
- Joined: 07:18 am Nov 24 2004
- Country:
- Location: Québec:North Pole
- Contact: