91 KDX200 float height
-
- Member
- Posts: 26
- Joined: 11:06 am Apr 13 2013
- Country:
91 KDX200 float height
I'm planning on cleaning my carb in my 91 KDX200 and I wanted to make sure the float what set right, does anybody know that stock height for it?
-
- Member
- Posts: 41
- Joined: 03:02 pm May 02 2013
- Country:
- Location: Hermon NY
Re: 91 KDX200 float height
good question, I just set my 94 so that it shuts just before the floats are level. same as I would do with my hondas.
-
- Member
- Posts: 222
- Joined: 08:51 am May 30 2012
- Country:
Re: 91 KDX200 float height
The manual says 16 +- 1mm. Here's a pic.
-
- Member
- Posts: 26
- Joined: 11:06 am Apr 13 2013
- Country:
Re: 91 KDX200 float height
What does it mean by 16 + 1mm? I'm new to this
-
- Member
- Posts: 26
- Joined: 11:06 am Apr 13 2013
- Country:
Re: 91 KDX200 float height
What does it mean by 16 + 1mm? I'm new to this
-
- Member
- Posts: 222
- Joined: 08:51 am May 30 2012
- Country:
Re: 91 KDX200 float height
Look at the float height measurement section on that page. You want the number 4 measurement to be between 15 and 17 mm.
Follow the directions from that section and the note right below it and you will be fine.
Follow the directions from that section and the note right below it and you will be fine.
-
- Member
- Posts: 26
- Joined: 11:06 am Apr 13 2013
- Country:
91 KDX200 float height
I adjusted my float but still nothing. I sit there and kick and kick and kick. Sometimes it will spill gas out of the overflow tube from the carb. Think maybe a spark plug?
- KDXGarage
- KDXRider.net
- Posts: 14130
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: 91 KDX200 float height
dirty valve needle?
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
-
- Member
- Posts: 26
- Joined: 11:06 am Apr 13 2013
- Country:
Re: 91 KDX200 float height
Like, float needle? When I looked at it, it wasn't dirty. I cleaned the whole carb up and down.
- KDXGarage
- KDXRider.net
- Posts: 14130
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: 91 KDX200 float height
It is the cone shaped, rubber tipped piece that is supposed to stop the flow of fuel into the bowl. A dirty/damaged bore or dirty/damaged rubber tip can cause a leak.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
-
- Member
- Posts: 41
- Joined: 03:02 pm May 02 2013
- Country:
- Location: Hermon NY
Re: 91 KDX200 float height
thank for the info. diagram is great help. scrambler if your getting gas to the carb u may want to check the plug. bill