new Lectron Billetron Pro Series fitment on KDX200 / KDX220

[Kevbot]

I played around with ti some more and cut the threads on the 90* adjusted to get it shorter to get some more cable length but still can't get it to bottom out. I might have to look at the KX or another cable. I am using 1/2" risers and CR fat bars (not cut)

[Chuck78]

The standard Lectron cable offering should work for you I'm betting, it works for the older Lectron carb but could use a 90° elbow also, but should work great with a Motion Pro Turbo throttle or other aftermarket pulley type throttle. The pulley adds a bit of length but gives the cable an easier life due to less friction.

Sorry you had to buy the Lectron elbow to find it was too long.
I do have an extra Motion Pro KX cable that may work for you if you can wait for me to mail it.
That or the Malossi short radius 90° elbow should be what you need.

[Kevbot]

Lectron actually sent the elbow free of charge otherwise I would've gotten the same as yours. How much do you want for the KX cable, I would buy it from you vs ebay or motion pro directly?

[Kevbot]

Ended up buying a motion pro KX cable for $12, once it gets here I will get it installed.

[Kevbot]

I didn't like how the 90 elbow came off the carb and mated with the throttle cable. I thought I would heat up the 90 and bend it to a less aggressive angle, when I went to bend it, it snapped right at the 90.

I went ahead and ordered the Sudco 40* https://www.ebay.com/itm/394000427103 which comes of the carb at a way better angle to the throttle cable, and I am back to using the stock KDX cable!

I will try and snap some photos tonight.

[Kevbot]

Was able to get out yesterday afternoon and test the new top end and carb, it was a whole lot of fun! I still need to do some tuning on the lectron as it seems to not like just cruising throttle at 1/4-1/3 twist.

One side of the carb does seem pretty full since it sits at a slight angle.

Idle/first start no adjustments: https://www.youtube.com/shorts/2q6PhDy5Y9g

[jedidan45]

Was able to get out yesterday afternoon and test the new top end and carb, it was a whole lot of fun! I still need to do some tuning on the lectron as it seems to not like just cruising throttle at 1/4-1/3 twist.

One side of the carb does seem pretty full since it sits at a slight angle.

Idle/first start no adjustments: https://www.youtube.com/shorts/2q6PhDy5Y9g

Hey Kevbot, thanks for the pics and video...any chance you have a pic of the top of the carb where the elbow and tank area are?

[Cornelius]

I got my Billetron Pro 38 installed the other day on my '98 220 with the vforce reeds.
Fitment is near perfect; tight but it fits.
Used stock throttle and throttle cable, everything backed off to the max.

[Chuck78]

Alright! We're getting some more Billetron Pro Series KDX users now!

[Kevbot]

Was able to get out yesterday afternoon and test the new top end and carb, it was a whole lot of fun! I still need to do some tuning on the lectron as it seems to not like just cruising throttle at 1/4-1/3 twist.

One side of the carb does seem pretty full since it sits at a slight angle.

Idle/first start no adjustments: https://www.youtube.com/shorts/2q6PhDy5Y9g

Hey Kevbot, thanks for the pics and video...any chance you have a pic of the top of the carb where the elbow and tank area are?

Yeah I will grab some pics, getting the itch to ride with this nice weather we have been having. Need to finish up a couple things and get the carb tuned a little better. I have a dead spot on the low end power, idles great and up top it screams. Also ordered a boyseen rad valve since my boot might be leaking a bit with the Vforce 3.

[mthendri]

Alright! We're getting some more Billetron Pro Series KDX users now!

Hi everyone! Add me to the list of Pro Series KDX users for my 2005 KDX 220. Hunter at Lectron support pointed me to this topic because I was running into some issues with the throttle cable. I ended up replacing the stock with a replacement and used the 90 degree bend supplied by Lectron.

I had a heck of a time getting the Lectron to fit "nicely" - as in getting the airboot to slide over the large part of the Lectron and then being able to get the smaller side in towards the motor was tricky....all while keeping the top angled just right to not hit the frame :-)


My next issue was the looooong stock petcock/fuel tap pushing up against the choke. I ordered the one linked here from partzilla and hope that sorts me out.

I mostly wanted to say thanks to those of you who've contributed to this topic - it's been very informative!

[Chuck78]

If you have a Boyesen RAD Valve, those should fit an unmodified Billetron a lot better than the stock intake with a VForce3 or VForce4 reed block. The airbox bell long body adapter I had Lectron machine down almost to the dimension of the PWK 35, but there's not enough material to go all the way down as I mentioned before. It fits fine when reduced to within a millimeter or two of stock diameter. It's not that much bigger anyways, but I didn't want to stretch out the air box boot too much. The RAD Valve coupler is an easy piece to replace or even source an alternate silicone coupling for, so that's less concerning.

[Chuck78]

The cable elbow that Lectron supplies still isn't really what's best. That custom order Barnett cable based on the drawing with the part number "Todd Miller" is really what Lectron should be selling for a multitude of bikes, not just 95 and up KDX. My stock universal Lectron cable broke right where it makes the sharp bend between the carb and the gas tank. It's also a high quality Barnett cable, but the only flaw is that it didn't have a 90° or 70° elbow with a Teflon liner sleeve in it.

[Chuck78]

Has anyone tried the Xcelerator metering rod for the Billetrons yet?

I'll be looking to get one of those this summer when I get back from a long road trip this month. That's really going to be the absolute ultimate carburetor setup for a KDX...
They weren't available yet last summer when I was working with Matt from Lectron to test fit the Billetrons to the 95 and up KDX, but now you can get them as an add-on option when you buy the Billetron new.