Can I run this slide or do I need a new one?
-
- Supporting Member II
- Posts: 7
- Joined: 09:50 pm May 21 2018
- Country: USA
- Location: Southern Maryland
Can I run this slide or do I need a new one?
I am cleaning the carb on my 01 220 and saw this chip on the top of the slide. Can I still run it or do I need a new one? I'm going to replace the reeds too and was thinking of going with the boyeson dual stage power reeds. Any experience with them? thanks
- MoonStomper
- Gold Member
- Posts: 561
- Joined: 02:05 pm Jun 02 2020
- Country: USA
- Location: Blacksburg, Virginia
- Contact:
Re: Can I run this slide or do I need a new one?
How does that even happen?
~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
-
- Member
- Posts: 48
- Joined: 10:23 pm Oct 31 2020
- Country: United States
- Location: NJ
Re: Can I run this slide or do I need a new one?
Make sure there are no burrs that could potentially impact the action of the slide. Other than that you should be ok. From my reading the 607 reeds are popular for the KDX.
- KDXGarage
- KDXRider.net
- Posts: 14060
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Can I run this slide or do I need a new one?
Can you? Yes.
Should you? :-)
Take extra care to grind and sand away the divot. The area around it looks really scratched up like it had been ingesting dirt / sand for a while. Check your carb bore surface.
Should you? :-)
Take extra care to grind and sand away the divot. The area around it looks really scratched up like it had been ingesting dirt / sand for a while. Check your carb bore surface.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
-
- Supporting Member II
- Posts: 7
- Joined: 09:50 pm May 21 2018
- Country: USA
- Location: Southern Maryland
Re: Can I run this slide or do I need a new one?
thanks guys
-
- Supporting Member II
- Posts: 7
- Joined: 09:50 pm May 21 2018
- Country: USA
- Location: Southern Maryland
Re: Can I run this slide or do I need a new one?
My cable dust boot was cracked and I ride through a lot of mud and puddles. Apparently, it got into the carb over time.
- KDXGarage
- KDXRider.net
- Posts: 14060
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Can I run this slide or do I need a new one?
I hope your cylinder walls and piston sides (and main bearings / small end / big end bearing) don't look the same.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
-
- Supporting Member II
- Posts: 7
- Joined: 09:50 pm May 21 2018
- Country: USA
- Location: Southern Maryland