USD 43mm Fork valving

Discussion specific to the 1991 - 1994 KDX250 sold in the USA
Post Reply
Liberated
Member
Posts: 5
Joined: 01:13 pm Jan 31 2015
Country:

USD 43mm Fork valving

Post by Liberated »

I'm sure I'm beating a dead horse here but I thought I would share my experience with the stock KYB 43mm fork. I just picked up a fairly low hour 92 250 and really love the motor.... hate the suspension. I took it out once to Holister Hills and was glad for all the power... it was more comfortable to Wheelie over everything then have the fork try to control the bumps... After much searching I know my only way to go would be to swap out for a later model front end... well, the fleebay is pretty picked over and this was supposed to be a budget friendly 2 stroke for me to play with.

I ended up disassembling the fork and contemplating how the fluid moves through the basevalve. It was much different then I was prepared for. I ended up Modifying the piston and check plate myself for better flow and purchased a set of springs for my weight...

Now I know there are few of these around and even fewer with the stock forks.. but I'm here to tell you, they can be modded and you can get really good performance from them!! I actually enjoy riding it now... it performs nearly as well as my 2008 Husqvarna with properly valved forks.
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Welcome to the forums. Can you describe more about what you did to the forks?
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
Liberated
Member
Posts: 5
Joined: 01:13 pm Jan 31 2015
Country:

USD 43mm Fork valving

Post by Liberated »

Sure thing. A condensed version.. I measured the port area on the piston and check plate. The fluid has to pass through the check plate first before it can flow through the piston. I found the plate's ports had 40% of the area of the piston's ports... So I enlarged and shaped the ports on both the check plate and the base valve piston. I was sure the changes would allow more oil flow, however I was not sure the flow would have a meaningful effect. An item of note is that the clicker port is a very small percentage of the overall available port flow... so adjustments at the bottom of the fork leg really offer only fine tuning...
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Are you talking about the stock part, as I have shown on the left of my picture?

Thanks.

Image
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
Liberated
Member
Posts: 5
Joined: 01:13 pm Jan 31 2015
Country:

USD 43mm Fork valving

Post by Liberated »

Yes, I am speaking of the stock valve. I had heard there were gold valves available at one time, however I understood they are no longer available. I also posted in my original post that this was to be a budget bike for me to play with. A free mod to the stock piston that works is awesome in my book.
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Hopefully the Race Tech Gold Valves are still for sale for the KDX's.

That is indeed an awesome job. I have heard of someone doing that to a more modern KX piston, but did not think of that on the KDX250 piston. Great job to make it better for you!

Where did you find springs? I have recently seen a couple of guys paying $170 or so for older model KX springs that are custom made. That sounds pretty expensive.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
Liberated
Member
Posts: 5
Joined: 01:13 pm Jan 31 2015
Country:

USD 43mm Fork valving

Post by Liberated »

I ended up contacting Cannon Racecraft in OK... they will wind you anything you want, but their stock springs are a bit cheaper if they fit your bill. They had a set just right for me on their dimensional list, so I grabbed them. I would post some photos of the piston mods..... if I could only figure out how to upload them.... Perhaps I need glasses.
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Ah, yes they make custom springs.

Usually photobucket and other sites can host pictures.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
snopro753
Supporting Member
Posts: 46
Joined: 06:06 pm Dec 11 2014
Country:

Re: USD 43mm Fork valving

Post by snopro753 »

Long shot, but I sent Liberated a PM and would like to get his pictures so I can post them here for others and myself to see.
Liberated
Member
Posts: 5
Joined: 01:13 pm Jan 31 2015
Country:

Re: USD 43mm Fork valving

Post by Liberated »

Apparently I'm not authorized to view pm's,.... I guess they will die with me :grin:
User avatar
snopro753
Supporting Member
Posts: 46
Joined: 06:06 pm Dec 11 2014
Country:

Re: USD 43mm Fork valving

Post by snopro753 »

Here are the pictures Liberated sent me of his mod of the KDX250 Fork Piston

Image

Image

Image

Image

Image
User avatar
snopro753
Supporting Member
Posts: 46
Joined: 06:06 pm Dec 11 2014
Country:

Re: USD 43mm Fork valving

Post by snopro753 »

Liberated, thank you for sending me the pictures. I have posted them above. How did you chamfer and enlarge the holes? Dremel? Looks like a steady hand is needed.
User avatar
Chuck78
Supporting Member II
Supporting Member II
Posts: 609
Joined: 06:20 pm Nov 30 2016
Country: USA
Location: Columbus, OH

Re: USD 43mm Fork valving

Post by Chuck78 »

Any chance of getting these photos and any additional tips on this re-posted? Were the valving spring shim washers in the base valve reconfigured as well?
'97 KDX220R - purple/green! - KLX forks, Lectron, FMF, Tubliss
'99 KDX220R project - '98/'01 RM125 suspension, Titanium hardware, Lectron Billetron Pro, Tubliss
'77 Suzuki PE250 & '83 Suzuki PE175 Full Floater - restomod projects
'77 Suzuki GS750-844cc, '77 GS400/489cc & '77 GS550/740cc projects
'62 GMC 1000 Panel Truck
'88 Suzuki Samurai TDI/Toyota swaps
'88 Toyota 4x4 pickup
MikNY
Member
Posts: 37
Joined: 04:59 pm May 14 2012
Country:
Location: Orange County NY

Re: USD 43mm Fork valving

Post by MikNY »

Trying to rehab some usd 43 from my 94, anyway to get these pics back?
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Yeah. I would like to see them, too. I need to try to email him.

What are you looking to do on your forks? I have a pic of some I took all the way apart years ago... Somewhere on my laptop
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

I sent snopro a PM. We shall see.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
snopro753
Supporting Member
Posts: 46
Joined: 06:06 pm Dec 11 2014
Country:

Re: USD 43mm Fork valving

Post by snopro753 »

I got your PM. I need to look through my old hard drive for these pictures. If I find them I will post them again.
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

Great! Thanks!
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
snopro753
Supporting Member
Posts: 46
Joined: 06:06 pm Dec 11 2014
Country:

Re: USD 43mm Fork valving

Post by snopro753 »

Image
Image
Image
Image
Image
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: USD 43mm Fork valving

Post by KDXGarage »

THANK YOU, snopro753!!

:partyman: :supz: :boogie: :prayer:
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
Post Reply