Installing 01 wr250f fastway pegs on a 93 kdx200

Discussion specific to the 1989 - 1994 (E Series) KDX200 model sold in the USA
Post Reply
DCKilla
Member
Posts: 5
Joined: 06:31 pm Jul 17 2021
Country: United States

Installing 01 wr250f fastway pegs on a 93 kdx200

Post by DCKilla »

I kept my footpegs from my old wr in hoping to use them on my kdx. The mount angle was the same. That was pretty much the deciding factor. Everything thing else could be dealt with. The footpeg, sleeve, and spring are from fastway for the 01 wr.

Starting with fitment and measurements. As you can see, there is a bit that needs to be removed from the spring side. The inside demension is a little over 23mm or .909 in. The mounting pin is exactly the same size needed.
20210717_151917.jpg
20210717_151917.jpg (2.42 MiB) Viewed 2389 times
20210717_152035.jpg
20210717_152035.jpg (2.8 MiB) Viewed 2389 times
I cut the spring side of the sleeve to make the entire length 23mm. After that, i assembled the peg by inserting the sleeve and placing the spring.
20210719_231729.jpg
20210719_231729.jpg (3.76 MiB) Viewed 2389 times
20210719_232023.jpg
20210719_232023.jpg (3.11 MiB) Viewed 2389 times
Finally, i installed the peg on the mount. With the modified fastway peg, it looks to be a 1/2in height adjustment depending which side of the peg you insert the sleeve.
20210719_231556.jpg
20210719_231556.jpg (3.14 MiB) Viewed 2389 times
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: Installing 01 wr250f fastway pegs on a 93 kdx200

Post by KDXGarage »

Sweet! That looks great.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
bufftester
Platinum Member
Platinum Member
Posts: 3455
Joined: 06:03 pm Oct 31 2012
Country: USA
Location: University Place, WA

Re: Installing 01 wr250f fastway pegs on a 93 kdx200

Post by bufftester »

Nice work. This will help out the H/220 model folks as well. Just too bad that Kawi didn/t use bolt on peg mounts instead of welded ones, would make the aftermarket much easier.
User avatar
Slick_Nick
Supporting Member
Posts: 1675
Joined: 10:06 pm Oct 22 2009
Country: Canada
Location: Calgary, Alberta
Contact:

Re: Installing 01 wr250f fastway pegs on a 93 kdx200

Post by Slick_Nick »

bufftester wrote: 02:40 pm Jul 20 2021 Nice work. This will help out the H/220 model folks as well. Just too bad that Kawi didn/t use bolt on peg mounts instead of welded ones, would make the aftermarket much easier.
But that's part of the reason they were able to keep the KDX so affordable!
'00 KDX 220R
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: Installing 01 wr250f fastway pegs on a 93 kdx200

Post by KDXGarage »

indeed!!
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
Post Reply