RM200 hybrid

Discussion for swapping a KDX motor in a MX frame...
Post Reply
maxbrad3r
Member
Posts: 3
Joined: 07:10 pm Nov 12 2024
Country: USA

RM200 hybrid

Post by maxbrad3r »

I was looking at possibly building myself a hybrid when I stumbled upon this bike on marketplace. It's a 2001 rm125 frame with a 2006 kdx200 motor. I picked it up for $1200 but it was pretty rough. I bought it from an 18 year old who had no clue what he had. He was trying to use it as a dunes bike to keep up with yfz quads. He did nearly no macitence from what I could tell BUT the oil was not sparkly just milky from a leaky water pump. I haven't actually ridden the bike formally yet. So far ive replaced basically everything but the frame, engine, the custom mounts, and tank. Everything else is getting replaced or will be over time. The engine was in great condition but the rear sprocket was bent the caliper broken, the rotor was gone, pads destroyed. The spokes were not all there. The swing arm was helicoiled very poorly and needed replacing. Subframe was bent and got replaced. whole chain assembly replaced. new radiators and guards. all new hoses. new levers. and eventually the plastics and graphics. I am trying to keep as much as was salvageable ( fmf gnarly I welded and expanded) because for my first stage of this build I'm trying to keep it at $2300 this will be getting the bike to a comfortable ridable state. the top and bottom end were both in great condition when I inspected them. there's much more to list but its nit picky you get the point. After this my plan is to restpring and revalve the suspension and then I'll be tearing apart the engine. Weisco crank, weisco top end, forged clutch basket, v force reeds, magura hydro clutch. During all this I'll be redoing the wiring cause as of now it's a mess. There's an amazon front headlight that's somehow been wired in ill be leaving it be tell I redo it all. This is my first post of hopefully several. I think I might've just found a gem when buying but maybe not. I'll try to update as I finish my first stage of the build and then on as I upgrade. I'm not inclined enough yet to add pictures but when I figure it out I'll update!
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14352
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: RM200 hybrid

Post by KDXGarage »

Welcome aboard. You have bought yourself an adventure AND a bike. Good luck with turning it into YOUR ride, YOUR way!

Look in my signature for instructions on adding pictures.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
User avatar
Chuck78
Gold Member
Gold Member
Posts: 916
Joined: 06:20 pm Nov 30 2016
Country: USA
Location: Columbus, OH

Re: RM200 hybrid

Post by Chuck78 »

Great suspension and chassis on the RM125's, and '01-'04 RM125 got the really good Showa stuff, while the RM250 got KYB until '05 when both had Showa suspension...
Send the original crank out for a rebuild with a Wossner or Vintco forged rod, or go with a new Vintco crank. Wossner or Vintco piston as well, it's a step or two above the Wiseco and Wossner comes in 69.00 A, 69.01 B, & 69.02mm C sizes for slight variations in plating wear and diamond-honing size, Vintco is Wossner but only A-sized (both have coated piston skirts, Wiseco does not), & Wiseco only comes in 69.00mm bore size or a 1.00mm overbore for 70.00mm, no B & C size selections.
'97 KDX220R - purple/green! - KLX forks, Lectron, FMF, Tubliss
'99 KDX220R project - '98/'01 RM125 suspension, Titanium hardware, Lectron Billetron Pro, Tubliss
'77 Suzuki PE250 & '83 Suzuki PE175 Full Floater - restomod projects
'77 Suzuki GS750-844cc, '77 GS400/489cc & '77 GS550/740cc projects
'62 GMC 1000 Panel Truck
'88 Suzuki Samurai TDI/Toyota swaps
'88 Toyota 4x4 pickup
User avatar
Chuck78
Gold Member
Gold Member
Posts: 916
Joined: 06:20 pm Nov 30 2016
Country: USA
Location: Columbus, OH

Re: RM200 hybrid

Post by Chuck78 »

'97 KDX220R - purple/green! - KLX forks, Lectron, FMF, Tubliss
'99 KDX220R project - '98/'01 RM125 suspension, Titanium hardware, Lectron Billetron Pro, Tubliss
'77 Suzuki PE250 & '83 Suzuki PE175 Full Floater - restomod projects
'77 Suzuki GS750-844cc, '77 GS400/489cc & '77 GS550/740cc projects
'62 GMC 1000 Panel Truck
'88 Suzuki Samurai TDI/Toyota swaps
'88 Toyota 4x4 pickup
User avatar
Chuck78
Gold Member
Gold Member
Posts: 916
Joined: 06:20 pm Nov 30 2016
Country: USA
Location: Columbus, OH

Re: RM200 hybrid

Post by Chuck78 »

'97 KDX220R - purple/green! - KLX forks, Lectron, FMF, Tubliss
'99 KDX220R project - '98/'01 RM125 suspension, Titanium hardware, Lectron Billetron Pro, Tubliss
'77 Suzuki PE250 & '83 Suzuki PE175 Full Floater - restomod projects
'77 Suzuki GS750-844cc, '77 GS400/489cc & '77 GS550/740cc projects
'62 GMC 1000 Panel Truck
'88 Suzuki Samurai TDI/Toyota swaps
'88 Toyota 4x4 pickup
maxbrad3r
Member
Posts: 3
Joined: 07:10 pm Nov 12 2024
Country: USA

Re: RM200 hybrid

Post by maxbrad3r »

How I bought it
IMG_0534.jpeg
IMG_0534.jpeg (295.25 KiB) Viewed 1027 times
IMG_0533.jpeg
IMG_0533.jpeg (265.69 KiB) Viewed 1027 times

How it’s sitting now
IMG_7282.jpeg
IMG_7282.jpeg (3.19 MiB) Viewed 1027 times
IMG_7292.jpeg
IMG_7292.jpeg (2.73 MiB) Viewed 1027 times
IMG_7289.jpeg
IMG_7289.jpeg (2.88 MiB) Viewed 1027 times
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14352
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: RM200 hybrid

Post by KDXGarage »

Wow at the radiator cage!!
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
maxbrad3r
Member
Posts: 3
Joined: 07:10 pm Nov 12 2024
Country: USA

Re: RM200 hybrid

Post by maxbrad3r »

KDXGarage wrote: 02:16 am Nov 15 2024 Wow at the radiator cage!!
Thanks! Amazon special it don’t look to shabby
Post Reply