Re: need some help pls not sure where locating pin go
Posted: 03:48 am Mar 07 2020
.......
Ooops, do you see 610 on the diagram? Is this the pin that was loose?
KDXRIDER.NET
Discussion group for KDX enthusiasts
https://kdxrider.net/forums/
need some help pls not sure where locating pin go
Page 2 of 3
Re: need some help pls not sure where locating pin go
Posted: 03:56 am Mar 07 2020
Re: need some help pls not sure where locating pin go
Posted: 03:58 am Mar 07 2020
Are you able to take a picture of your bike? It would be helpful to see what you are seeing.
Thank you.
Thank you.
Re: need some help pls not sure where locating pin go
Posted: 04:45 pm Mar 08 2020
0ops_sorry wrote: ↑02:48 am Mar 07 2020...one more thing what kind sleeve do i buy also size of the piston send link pls ebay only..
I can't believe no one has said anything yet! I would not recommend sleeving your cylinder! Send it off to have it replated. An improperly done sleeve will ruin your cylinder. With the cost of machining it for the sleeve, the cost of the sleeve itself, and the labor for doing it, you might as well have it repaired/plated properly by Millenium.Re: need some help pls not sure where locating pin go
Posted: 07:05 pm Mar 08 2020
rip i send my cylinder to some guy from ebay to get it sleeve rip my life sadface thanks for helpin out tho <3 i like to donateSS109 wrote: ↑04:45 pm Mar 08 20200ops_sorry wrote: ↑02:48 am Mar 07 2020...one more thing what kind sleeve do i buy also size of the piston send link pls ebay only..
Re: need some help pls not sure where locating pin go
Posted: 01:02 am Mar 09 2020
He could keep an eye out for a used cylinder on eBay and maybe sell the sleeved one on eBay.SS109 wrote: ↑04:45 pm Mar 08 20200ops_sorry wrote: ↑02:48 am Mar 07 2020...one more thing what kind sleeve do i buy also size of the piston send link pls ebay only..
Re: need some help pls not sure where locating pin go
Posted: 04:36 pm Mar 09 2020
Can someone link the problems associated with going with a steel sleeve in the kdx cylinder? I’ve read slight difficulties when going that route
Re: need some help pls not sure where locating pin go
Posted: 05:43 pm Mar 09 2020
The disadvantages of sleeves are: less durable than plating, higher friction, worse heat transfer characteristics, and porting can have poor match/transition to cylinder.Kdxfan4130 wrote: ↑04:36 pm Mar 09 2020 Can someone link the problems associated with going with a steel sleeve in the kdx cylinder? I’ve read slight difficulties when going that route
That said, If you've already bought the sleeve, just run it.
Re: need some help pls not sure where locating pin go
Posted: 06:28 pm Mar 09 2020
And it costs the same as a replate.
Re: need some help pls not sure where locating pin go
Posted: 06:33 pm Mar 09 2020
What they said!
Re: need some help pls not sure where locating pin go
Posted: 12:11 pm Mar 20 2020
sarrant wrote: ↑05:43 pm Mar 09 2020The disadvantages of sleeves are: less durable than plating, higher friction, worse heat transfer characteristics, and porting can have poor match/transition to cylinder.Kdxfan4130 wrote: ↑04:36 pm Mar 09 2020 Can someone link the problems associated with going with a steel sleeve in the kdx cylinder? I’ve read slight difficulties when going that route
That said, If you've already bought the sleeve, just run it.
Re: need some help pls not sure where locating pin go
Posted: 12:49 pm Mar 20 2020
got my sleeve todayKdxfan4130 wrote: ↑04:36 pm Mar 09 2020 Can someone link the problems associated with going with a steel sleeve in the kdx cylinder? I’ve read slight difficulties when going that route
Re: need some help pls not sure where locating pin go
Posted: 01:26 pm Mar 20 2020
All right! Take your time during reassembly. Don't forget about the left hand threads on the shaft and nut of the power valve system advancer rod.
Re: need some help pls not sure where locating pin go
Posted: 05:40 pm Mar 20 2020
Re: need some help pls not sure where locating pin go
Posted: 07:57 pm Mar 20 2020
Since you had it done, and if you don't mind saying, which company did you use for the sleeve and what was your total cost for it?
Re: need some help pls not sure where locating pin go
Posted: 08:08 pm Mar 20 2020
Put some oil in there too.
Re: need some help pls not sure where locating pin go
Posted: 08:54 pm Mar 20 2020
Looks like a nice job. Now you can bore it to the next oversize. Are there oversized piston kits available? Or do you need to find a piston off another brand I.e. Yamaha?
Re: need some help pls not sure where locating pin go
Posted: 01:15 pm Mar 21 2020
SERVICE was $120 https://www.ebay.com/usr/lynncampspeedshop-fb he did a good job bought a new piston and la sleeve total cost i say around 300
Re: need some help pls not sure where locating pin go
Posted: 03:41 pm Mar 21 2020
Thank you. This info will be helpful to others in the future if they are considering having their cylinder sleeved.0ops_sorry wrote: ↑01:15 pm Mar 21 2020SERVICE was $120 https://www.ebay.com/usr/lynncampspeedshop-fb he did a good job bought a new piston and la sleeve total cost i say around 300
Re: need some help pls not sure where locating pin go
Posted: 10:57 pm Mar 23 2020
done!!! <3 start in the 5th try maybe 7 loolSS109 wrote: ↑03:41 pm Mar 21 2020Thank you. This info will be helpful to others in the future if they are considering having their cylinder sleeved.0ops_sorry wrote: ↑01:15 pm Mar 21 2020SERVICE was $120 https://www.ebay.com/usr/lynncampspeedshop-fb he did a good job bought a new piston and la sleeve total cost i say around 300